C-244 | Anti-Siphon Design

PRIER C-244 provides a year round source of water in areas that are subject to freezing temperatures. The hydrant valve is connected to the supply piping in the heated portion of the structure, eliminating the possibility of freezing. Ordering the C-244 gives you the same style hydrant but with a vandal proof extended lockshield and operating key.

The PRIER C-244 has all the characteristics of the historically proven C-134 with the added protection of an anti-siphon vacuum breaker and backflow check valve. It is available from stock in lengths from close coupled to 24”, longer sizes are available on request.

 

Like this wall hydrant, but want it with a handle? Check out the C-144. 

Product Support

PRIER has been manufacturing the C-144/244 Freezeless Hydrants since 1990. This freezeless hydrant has truly passed the test of time. It is a simple operating product that is fairly simple to repair. Possible Repair Issues for the C-244 Freezeless Wall Hydrant include:

1. When the water is running, water leaks out from behind the handle

This is a common maintenance occurrence for any packed valve of any brand or manufacture. It is overcome by simply tightening the packing nut with a crescent wrench. This will force the packing tighter around the stem to eliminate leakage.

Occasionally, the packing will need to be replaced if the packing nut has been repeatedly tightened.

The part required for this is a C-134KT-803 Packing Kit

C-134KT-803 Packing Kit

Click here to watch the video

2. The hydrant drips after shut off

A freezeless wall hydrant shuts off inside the heated portion of the structure therefore, the water inside the hydrant will drain out after shutoff. The shutoff point could be any distance from 4" to 24" inside the structure. This installation should also be pitched to allow the water to easily drain out of the hydrant. The hydrant may drip for up to 60 seconds after shutoff. If the water continues to drip after that time, you most likely need to replace the bibb washer.

PRIER uses a OO Beveled Bibb Washer for the C-244 freezeless wall hydrant, part number C-134KT-802. The bibb washer is a standard "OO" Beveled Bibb Washer, also available at your local plumbing wholesaler.

C-134KT-802 Replacement Bibb Washer

Click here to watch the video

3. Water leaks from under the plastic cap on top of the valve

The vacuum breaker has begun to leak. This problem often occurs when the hose is left on the valve and the plastic cap is ruptured by freezing, or the rubber seating surface needs to be replaced.

The replacement kit for this repair is part number C-144KT-806.

C-144KT-806 Vacuum Breaker Replacement Kit

*PLEASE NOTE: Since the creation of this video, we have updated our vacuum breakers to aluminum caps as shown above. The C-144KT-806 and 630-7500 are now universal vacuum breaker kits and will fit all past and present PRIER and Mansfield style residential hydrants.

4. Water is leaking from the hydrant inside my house

Unfortunately, your freezeless hydrant is broken, most likely beyond repair. This happens when the water becomes trapped within the hydrant. The water freezes, expands and ruptures the copper shaft of the hydrant located on the inside the structure. The most common reason for this problem is leaving the garden hose attached during freezing weather, or the hydrant was not installed with the proper drainage pitch.

DO NOT OPERATE THE HYDRANT IF THIS HAS OCCURRED.

Please remove the handle to prevent accidental operation until the problem is repaired by your plumber.

5. The operating key is missing from my hydrant

For any one of numerous reasons, your operating key may be missing. PRIER's operating key is unique to its products - it has one flat side and the rest is rounded. This style key mates perfectly with our stem-end for a snug fit and years of reliable operation.

The required part number is C-108KT-808.

C-108KT-808 Operating Key

6. The operating key is missing from my hydrant

C-234KT-804 Handle Conversion Kit

Contents of this kit are as follows:

7. The stem end is damaged and I cannot operate the freezeless hydrant

Occasionally the stem of the PRIER hydrant gets damaged beyond repair. This is most commonly caused by the hydrant being operated by pliers and damage to the brass on the end.

To determine the proper replacement stem, you need to determine the following:

1. Overall length (OAL) of the stem, from tip to brass tip. Do not include the rubber bibb washer in this measurement.

2. Using the acquired dimensions, determine which stem is required from the chart below:

The following stems are for the C-144 Diamond Series Freezeless Hydrant (manufactured after Spring 2013):


The following stems are for the C-144 Series Freezeless Hydrant pre-Diamond Series (manufactured before Spring 2013):

6. I need a complete rebuild kit

The complete repair kit for the PRIER C-144 Anti-Siphon Freezeless Wall Hydrant is part number C-144KT-807. It contains all wearing parts for the item.

C-144KT-807 Rebuild Kit for C-144